Відео

Thank you for the detail on each component and explaination of the sunroof operation. This was incredibly helpful while I was hodgepodging two junkyard sunroof assemblies into one working one.

Just wodering wrap + 3m fabric?

Was there anything on the exhaust to give any clue. Cuz that sounds great would love to grab one up myself

Termikli fan iptal edip elektrikli fan bağlamak motora zarar vermezmi yani mühendisler elektrikli fan koyabilirdi termikli fanı uygun görmüşler belirli bir sıcaklığı korumak için olabilirmi mekanik fan ?

What about bucket seats? That way you wouldn’t have the two internal belt hooks. Where the harnesses points would be fixed?

Just wanted to say Thanks I’ve been wondering what that shake at like 50-60 mph was gonna try those bushings in the control arms!

Great video , is the oil specifically 5w-30 or can I use 5w-40 I believe that’s what the owners manual says , also I missed where the copper washer goes can some explain?

Thank you! This made everything sooooo much easier. I ended up having to remove the subframe bolt on one side but kept a few threads on the driver's side. Great walk-through. Thnaks again!

that intercooler has seen some days.

A czemu czujnik tak wysoko a nie powinien byc niżej.

Thanks for sharing. I just picked up a trailer kit from HF, and will be starting my buildout soon. Any tips 6 years after the video?

Hey there, I currently have 2007 non-Brembos, but I already have stainless steel lines installed. Would I need to order different stainless steel lines for these? Or would I be fine with my current SS lines? Thanks for the video!

I’m trying to get one is it smart to get one

Get a late model Chevy express van 3500. Ypu will need a camshaft, exhaust headders, a tune and helper springs. Make sure ypu check the brakes in the rear, those wear out much faster (I go for performance oriented front pads that brake better and wear faster to compensate a bit for the wear difference and the weight of the rig). Make sure yoj get a 3500 with a 6 speed, if you get a late model like a 2019 it will come with an L96 vortec engine (last and best version of the 6.0 vortec) and it should come with the 6L90 transmission, which is bulletproof. It likes premium fuel evennif it doesn't need it (91 octane). And get the long wheel base, it will actually help ypu a lot with towing dinamics. I own a 2019 3500 15 passenger express. I move people, heavy stuff and tow trailers with it. It is a beast, it has plenty of power and some simple mods will make your life even better. Just dont go too agressive with the cam and keep up the maintenance regularly (7k miles, complete mainteinance, sinthetic oil, 20k miles between transmission maintenance, 40k miles for the diff at most). The van should be able to move itself over 300k miles without an issue

Really curious about how much power the mechanical fan is taking now! Would be cool to see a dyno comparison

Concise and to the point! Do you have a video on how you did the mirrors?

Haha I made the mistake of removing the white box and the AC controls too. Thankfully I hadn't thrown them away and now their ziptied back in

Don’t do this, it trapped air in my g35. You cannot burp system without heat

What’s the box called

I mean I watched both videos. Attention spans a little bit lacking but just wanted to confirm if you can swap gear ratios between manual and autos? I was told no but on the Z1 website I'm pretty sure that they said it might be possible

Color is only a factor in the visible spectrum. Material type and finish determine thermal energy absorption. Search "emmisivty". Great video.

Great video mate 👍

Does the FX35 also use a 3.69 ratio

Do you have to put those big washers on front lower arm?

Me favorite tuning is stage 2+ for 3.0d engine❤

You just gonna blow all the bearings in you engine instead of spending 150$ more to get can a gel or stock damper that absorbs the knocking ... Bravo

Good job making the video, my rear window regulator just broke with the window stuck down, so this is helpful.

Q: Do you still own this MINI? Just curious. I have a 2020 3 door, seems all my noise is coming from the rear sill vent holes just below the hatch latch. Did you cover those? TIA.

Really hoping you see this and can get some insight from you I’m doing this exact same cooling setup. The only issue I am finding is that I cannot find that block off plate with the coolant port by the manifolds. Do you know if a company who makes them or would you be willing to make one and I could pay Would love to hear back from you, thanks

My benz had a service-mode already incorporated into the struts from factory. 😁

Does anyone know how good these are from a stop?

Where do u order that

watch the stud on some cars...on cars with the stud really close to the rear, you might have to go in at a slight angle or offset to 1 side...I'll use these bigger eyelets on my next HW keychains (started w/#216s)

Ich habe ein 15%Pully Rad verbaut was ist wenn ich die 2% Riemenscheibe noch verbaue schadet das den Motor Software ist schon geändert.Wollte eigendlich nur mehr durchzug keine Höhere Endgeschwindigkeit.

My only concern is leaving the vehicle quickly like a fire hazard. Lots of straps.

Rozpurka jest lepsza

A gdzie te części można kupić

Where do you purchase this?

God you Americans don’t half waffle on - yawn 🥱

I love your video. I have a question regarding the 12V power source during installation. Why couldn't you combine the power sources for the light bulb and the gauge itself to a single 12V power source say the radio in this case?

My window is not going back into the door

MI installed the 75 mm throttle body and bored out the plenum to match 75 mm. I also sanded and polished the upper and lower plenum. I did a ECU reset and throttle idle learn However, still have a service engine soon. Notice light. I cle ared that and it came back ten minutes later. Does anybody know what I should try next. The only other thing I did was replace spark plugs withNGK Ruthenium plugs.

I installed the 75 mm throttle body and bored out the plenum to match 75 mm. I also sanded and polished the upper and lower plenum. I did a ECU reset and throttle idle learn However, still have a service engine soon. Notice light. I cleared that and it came back ten minutes later. Does anybody know what I should try next.

I put a 85c calibrated thermostat on my 97 540i I owned about 5 years ago…. Worked fantastic and car ran cooler

one thing i noticed is most z owners wear adidas sneakers ❤

5w30 ??? why?

Does that white box only need to be there when you are tuning the factory ecu ? Or if I have a haltech stand alone can I get rid of the white box and AC controls ? Thankyou

Nice video. Concise and to the point.

I'm in the process of my weight reduction on my z this video helped me alot

worked perfect for a GTO hotwheel !!